PN80238A english:OG english 12/16/08 4:07 PM Page 1
8800-8849 Series
OWNER’S GUIDE
Guía del Dueño
L
e
G
u
i
d
e
d
u
PPropriiétaire
c
u
u
rek
r
ek
Before Returning, Call
Eureka Customer Service
Antes de enviar de regreso, Ilame al Servico al Cliente de Eureka
Avant de le retourner, appelez le service à la clientèle Eureka
HELPLINE LÍNEADEAYUDA LIGNE D’AIDE
1-800-282-2886
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturday - Sunday
8 a.m. a 7:30 p.m. (CST), de Lunes a Viernes
10 a.m. a 6:30 p.m. (CST), Sábado y Domingo
8 h à 19 h 30 (CST), lundi au vendredi
10 h à 18 h 30 (CST), samedi et dimanche
Upright Vacuum Cleaner
Household Type
Aspiradora Vertical
Tipo demestico
Aspirateur vertical
de type résidentiel
© 2009 Electrolux Home Care Products, Inc. Printed in China PN80238A
PN80238A english:OG english 12/16/08 4:08 PM Page 3
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the
electrical cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer's recommended attachments.
!
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to a service center before using.
• Do not pull or carry by cord. Do not use cord as a handle. Do not close a door on cord or pull cord
around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from
heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose
clothing, fingers, and all parts of body away from openings and moving parts.
• Do not place vacuum cleaner on furniture or stairs as the brush roll may cause damage. Use
extra care when cleaning on stairs. Place vacuum cleaner on floor with the handle in storage
position while using attachments.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust cup, filter screen, foam filter and HEPA exhaust filter in place.
• Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley
when servicing the drive belt.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where
they may be present.
• Store your vacuum cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
®
• Unplug before connecting Power Paw. Not for use on animals.
The Power Paw name is a registered trademark of Electrolux Home Care Products, Inc.
SAVETHESE INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
Motor
Do Not Oil the motor or the brush roll at any time. The bearings are permanently lubricated
and sealed.
Eureka Customer Service HELPLINE 1-800-282-2886
1
PN80238A english:OG english 12/16/08 4:08 PM Page 4
How to Identify Parts of Vacuum Cleaner
Handle
Dusting brush
Hose support
Power Paw®
Filter screen
Hose
On (I) / Off (O)
power switch
Tool caddy,
carrying handle &
upper cord wrap
Air path panel
behind dust cup
Hose wand
Power cord
Hose retainer
Dust cup & lever
Self-cleaning duster
Nested crevice tool
& extension wand
Foam and
filter frame
Duster activation knob
Quick release
cord wrap
HEPA filter
compartment
Headlight
Height adjustment knob
Handle release
EZ roll wheels
Brush roll cover
Edge cleaner windows
Maintenance Schedule
Maintenance schedule is also located on back side of dust cup.
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
Moving parts! Make sure power switch is in OFF (O) position before plugging in power cord.
!
EACH USE
DUST CUP – Empty
SLIDE LEVER TO CLOSE
SLIDE LEVER TO OPEN
PULL OUT
&
EMPTY
WEEKLY
FILTER SCREEN – Wash & Clean
Foam Filter
PMF-1
Filter Screen
RETURN
&
LOCK
REMOVE CLOCKWISE
WASH AND CLEAN
WEEKLY
FOAM PMF-1 & FILTER FRAME – Wash & Dry
Filter Frame
EXT-U Belt
HEPA
Filter HF10
REMOVE FOAM & FILTER FRAME
AIR DRY COMPLETELY
REINSTALL FILTERS
WASH
6 MONTHS
HEPA HF10 FILTER – Replace
Brush Roll
REMOVE FILTER FRAME
LAY FLAT & UNLOCK DOOR
REPLACE FILTER
REPLACE DOOR & LOCK
MONTHLY
BRUSH ROLL – Clean
EXT-U BELT – Replace a worn, cut or out of shape belt
2
Eureka Customer Service HELPLINE 1-800-282-2886
PN80238A english:OG english 12/16/08 4:08 PM Page 5
How to Use Accessories
!
Vacuum Cleaner handle must be in upright position
Telescopic Self-Cleaning Duster Use for furniture, blinds, pictures and high-reach areas. Can be
used in short or extended positions.
1) Activate static charge: Push power
switch ( I ) on and turn activation knob
for 10 seconds to clean or charge duster.
2) Turn vacuum off and remove duster
from cleaning chamber.
3) Short position: Dust low surfaces.
4) Extended position: Turn twist tabs
to extend. Push firmly to collapse
and turn to lock.
Be sure to raise height adjustment setting before using attachments.
!
Combination Crevice Tool
and Extension Wand
Use for baseboards, corners and
between cushions.
1) Grasp crevice tool near ridges and
pull apart.
2) Turn ridge end to center.
3) Push crevice tool into wand and place
on end of hose.
Dusting Brush Use for furniture,
drapes, blinds, bookshelves, lampshades
1) Remove hose from hose retainer
from back of vacuum.
2) Place dusting brush on end of hose,
wand or crevice tool.
Power Paw®
Stair Hose (hose available for purchase)
Use for furniture and stairs.
Make sure vacuum is below you,
pushed against the bottom step.
1) If model has additional stair hose,
attach to end of hose.
2) Attach Power Paw to the end of
wand or hose.
Make sure you turn off vacuum
before removing debris from
Power Paw.
Eureka Customer Service HELPLINE 1-800-282-2886
3
PN80238A english:OG english 12/16/08 4:08 PM Page 6
How to MaintainYourVacuum Cleaner
!
Make sure vacuum cleaner is turned off and power cord is unplugged.
Maintain Brush Roll
Motor can become hot with normal use.
Do not remove end caps. Remove hair and threads from brush roll periodically.
Check EXT-U Belt. Replace if worn, cut or out of shape
Avoid touching the motor shaft when checking brush roll or belt.
!
How to replace brush roll or belt
1) Use handle release to lower handle
flat onto floor. Turn vacuum over on its
backside and remove 4 screws (Fig. 1).
Œ
Ž
2) Turn vacuum over to front side and
remove brush roll cover (Fig. 2).
Fig. 1
Fig. 2
3) Remove brush roll and belt (Fig. 3).
4) Thread new belt around motor shaft
and then the brush roll (Fig. 4).
5) Insert left end of brush roll first and
then the right end (Fig. 5).
6) Rotate brush roll 2 turns to center belt.
Fig. 4
Fig. 3
7) Replace brush roll cover (Fig. 2). Turn
vacuum over on its backside.
Œ
8) Replace screws
&
closest to
˜ ™
the brush roll first. Then replace
screws (Fig 6).
&
Œ
™
˜
Fig. 5
Fig. 6
Change Light Bulb
Make sure vacuum is turned off and power cord is unplugged.
!
1) Remove HEPA filter. See directions
on page 2 for removing the HEPA filter.
2) Unscrew the lens and remove old
bulb (Fig. 7).
3) Push in new bulb, replace lens cover and
replace screw back into place (Fig. 8).
4) Replace HEPA filter, filter door, foam
filter and frame and secure dust cup.
Fig. 7
Fig. 8
Eureka Customer Service HELPLINE 1-800-282-2886
4
PN80238A english:OG english 12/16/08 4:08 PM Page 7
How to Clear a Blockage
Make sure vacuum is turned off and power cord is unplugged.
!
Hose Blockage (Fig. 1)
1) Remove hose from hose retainer. Flexing the hose will
help loosen any blockage.
2) Remove screw from hose connector and remove blockage.
3) Replace hose connector and screw; replace hose into
hose retainer.
Air Path Blockage (Fig. 2)
1) Remove dust cup to locate air path panel.
Remove 2 screws.
2) Remove debris in air path, replace the 2 screws
Fig. 1
Fig. 2
and secure dust cup.
The Eureka LimitedWarranty
Eureka warrants this vacuum cleaner to be free from
defects in material and workmanship for a term of one
year for normal household use. Warranty is granted
only to the original purchaser and members of
immediate household.
Authorized Warranty Station or Service Information, visit
www.eureka.com, write or telephone toll free:
USA: 1-800-282-2886 Mexico: (55) 5343-384 Canada: 1-800-282-2886
Electrolux Home Care
North America Service Division
P.O. Box 3900
Electrolux Home Care
Electrolux Home Care
North America Service Division
5855 Terry Fox Way
Peoria, IL 61612
Mississauga, Ontario L5V 3E4
This warranty is good for one year from the date of
purchase only when the vacuum cleaner is used in
the accordance with Eureka operating instructions.
Obtaining Warranty Service
OutsideYour Community
You must pay the shipping charges to the Eureka
This Warranty Does Not Cover
Authorized Warranty Station.
• Parts of the vacuum that require replacement under
normal use such as disposable dust bags, filters,
drive belts, light bulbs, brush roll, bristles, impellers
and cleaning.
Return Shipping Charges will be paid by the Warranty
Station. When returning parts for repair, please include
the model, type and serial number located on the rating
plate on the lower backside of the vacuum.
• Damages or malfunctions caused by negligence,
abuse, and use not in accordance with the
Owner’s Guide.
Further Limitations and Exclusions
Any warranty that may be implied in connection with your
purchase or use of the vacuum, including any warranty
of Merchantability or any warranty for Fitness For A
Particular Purpose is limited to the duration of this
warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitations
may not apply to you.
• Defects or damages caused by unauthorized
service or the use of other than Genuine Eureka,
ARM & HAMMERTM and FiltreteTM by 3M parts.
What Eureka Will Do
Eureka will, at its option, repair or replace a defective
vacuum or vacuum part that is covered by this warranty.
As a matter of warranty policy, Eureka will not refund
the consumer’s purchase price.
Your relief for the breach of this warranty is limited to
the relief expressly provided above. In no event shall the
manufacturer be liable for any consequential or incidental
damages you may incur in connection with your
purchase or use of the vacuum.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Warranty Registration
Please fill out and return the warranty registration card
accompanying your vacuum.
Obtaining Warranty Service
This warranty gives you specific legal rights.You may
also have other rights, which may vary by state.
The ARM & HAMMER name is a trademark of Church and Dwight Co., Inc.
3M and Filtrete are trademarks of 3M Company, used by Electrolux Home
Care Products, Inc. under license.
To obtain warranty service you must return the vacuum
or vacuum part along with “proof of purchase” to any
Eureka Authorized Warranty Station. For Eureka
Eureka Customer Service HELPLINE 1-800-282-2886
5
PN80238A english:OG english 12/16/08 4:08 PM Page 8
Thermal Cut-Off
This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum
suddenly shuts off, push the power switch to off (O) and unplug the vacuum. Check the vacuum for a possible source of
overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least
30 minutes before attempting to use the vacuum. After the 30 minute period, plug the vacuum back in and turn on the
switch. If the vacuum still does not work, take it to a Eureka authorized service center for repair or call 1-800-282-2886.
Problem Solving
!
Make sure vacuum is turned off and power cord is unplugged.
Solution
Problem
Cause
Power plug
Motor will not start.
• Push plug securely into outlet.
• Try another outlet.
• Check circuit breaker.
Power switch
• Turn power switch to on ( I ).
• See above.
Thermal cut-off
Vacuum does not
clean carpet or bare
floor.
Dust cup and filters
• Empty dust cup, clean and/or change filters.
• If picking up fine dust, the dust cup may not look full, but
a fine substance tends to reduce suction when it blocks
air flow through the foam filter and filter screen. Refer to
page 2 for filter maintenance. Make sure foam filter, filter
screen and dust cup are installed properly.
Belt
• Replace a worn, cut or out of shape belt. Page 4
Hose
• Remove any clogs from the hose that restrict the
airflow. Page 5
Bare floor setting
• For bare floor cleaning, turn height adjustment knob to
bare floor position.
Carpet height setting
Dust cup and filters
• For carpet cleaning, turn height adjustment knob to
another position.
No suction at the
end of hose.
• Empty dust cup, clean and/or change filters.
• If picking up fine dust, the dust cup may not look full, but
a fine substance tends to reduce suction when it blocks
air flow through the foam filter and filter screen. Refer to
page 2 for filter maintenance. Make sure foam filter, filter
screen and dust cup are installed properly.
• (Located above the dust cup). Check & clean debris to
maintain full air flow. Page 2
Filter screen
Hose
• Remove any clogs from the hose that restrict the
air flow. Page 5
Vacuum is hard
to push.
Vacuum height setting
•
Adjust knob to a higher position.
Belt
Belt
• Replace a worn, cut or out of shape belt. Page 4
Burning smell; brush
roll will not turn.
• Check brush roll for debris. Page 4
• Replace broken or out of shape belt. Page 4
Eureka Customer Service HELPLINE 1-800-282-2886
6
|