QUICK START GUIDE
Built-in oven
SETTING THE CLOCK
You set the clock within the user preference menu. To learn more about the user preference menu, refer to your User guide.
Note: If you do not wish to set the time initially when the oven is first switched on at the wall, press the cancel button to exit the clock setting.
If you want to set the clock later, follow the steps under ‘To change the time’.
NZ AU GB IE
To change the time
When the oven is first switched on at the wall
Keep this document handy for easy reference.
(within the user preference menu)
For detailed information on the other features of your oven, see your ‘User guide’.
Before using your oven, make sure you read the full ‘User guide’, with special attention to the ‘Safety and warnings’ section.
For contact information or if you require service, assistance or replacement parts, see the end of this document or your ‘Service & warranty’
booklet.
YOUR OVEN
1
2
3
4
5
6
7
8
9
Control panel
9
1
The display will flash 24 Hr.
2a Press the right scroll button to scroll
between 24 Hrand 12 H
2b Press the select button to confirm.
1
1
Press and hold the left and right scroll
buttons together for 3 seconds
Oven vent louvres
Step down oven wire shelf
Oven light
Telescopic sliding shelf
Side rack
Oven wire shelf
Oven door and handle
Oven seal
r
10
11
to enter the user preference menu.
2
The display will either show 12 Hror 24
H
r
2
3
Press the select
The display will flash.
Follow steps 2-5 left to set the time.
button to confirm.
3
4
12
5
6
7
OB60SL9DEX
13
14
At step 2a, you also now have the
ability to scroll between 24 Hr,
12 Hr and OFF (turns the display off).
Refer to the User guide to learn more
about this feature.
Accessories:
10 Grill rack
3
Press the left and right scroll
buttons to set the time.
4
Press the select
button to confirm.
11 Smokeless grill tray
12 Deep Roasting dish
13 Flat baking tray
14 Catalytic panels
The time set will now be steadily lit.
1 REMOVE ALL CABLE TIES & PACKAGING HOLDING
THE SHELVING IN PLACE
FIRST USE
8
Important!
Before using your oven for the first time, you should fit both
the Catalytic Panels (supplied). See ‘Care and cleaning’ in
your user guide for details about these self cleaning panels.
THE CONTROL PANEL
You do this by:
removing ALL the cable ties holding the shelving in place,
if the installer has not already done so.
removing the shelves and side racks
fitting the catalytic panels
Function dial
Function halo
Temperature
indicator
Temperature
dial
Function indicators
(see ‘Oven functions’)
Temperature
halo
FUNCTION
TEMPERATURE
replacing the side racks and shelves
We recommend you then condition the oven.
Follow the steps below to fit the Catalytic Panels.
3 REMOVE BOTH SIDE RACKS
2 REMOVE ALL SHELVES FROM THE OVEN
Rotisserie indicator
(see ‘Using the
Rotisserie’) in the
User guide
2
Timer indicator
(see ‘Using the
timer’)
Remove both side racks by 1)
pushing down on the retaining
wire until it clears the lower lock
stud and swing out wards to 2)
clear the upper lock studs, then
1
2
Remove all the shelving, taking special care with the telescopic
sliding shelves.
To remove a telescopic sliding shelf, grip it at the front (making
sure you are gripping the wire shelf and the sliding frame
together), lift upwards and pull it out of the oven.
For your safety, the wire shelf and telescopic sliding frame are
2
Cooking time indicator (see ‘Automatic cooking’) in User guide
if lit:
if lit:
Rotisserie is
in use
Control lock indicator (see
‘Locking the control panel’)
Timer is counting
down
if lit:
3) lift out.
Automatic cooking time is set
Display
lock stud
if lit:
built together as one unit and are not separable.
Control panel is locked
retaining wire
1
Locking the control panel
To lock, press and hold the select
button for 2 seconds.
To unlock, press and hold the
cancel
button for 2 seconds.
Stop time indicator
(see ‘Automatic cooking’) in User guide
Scroll
Select
Cancel
3
if lit:
Automatic stop time is set
continued over
|