DESKPOWER P300 Series User’s Manual
(Model: P301 / P310)
Fujitsu endeavours to ensure that the information in this document is correct, but accepts no liability
foranyerrororomissioninthesame.AnyproceduresdescribedinthisdocumentforoperatingFujitsu
products should be read and understood by the operator before such products are used. To ensure
that Fujitsu products function without risk to safety and health, such procedures should be strictly
observed by the operator. The development of Fujitsu products and services is continuous and
published information may not be up to date. Any particular issue of a product may contain facilities
not described herein. It is important to check the current position with Fujitsu. Specifications and
statements as to performance in this document are Fujitsu estimates intended for general guidance.
Theymayrequireadjustmentinparticularcircumstancesandshouldthereforenotbetakenasformal
offers or commitments.
DESKPOWERisatrademarkofFujitsuLimited. ThefollowingareregisteredtrademarksofMicrosoft
Corporation: MS, MS-DOS, Windows ® NT, Windows ® 98, Windows Millennium, Window ® 2000 and
Windows XP.
Intel and Pentium are registered trademarks of Intel Corporation in the U.S.
Celeron is a registered trademark of Intel Corporation in the U.S.
Other product names are trademarks or registered trademarks of respective companies.
Other products are copyrighted by individual companies.
All other trademarks referenced are trademarks or registered trademarks of their respective owners,
whose protected rights are acknowledged.
Copyright © Fujitsu PC Asia Pacific
All rights, including rights of translation, reproduction by printing, copying or similar methods, in part
or in whole, are reserved.
Offenders will be liable for damages.
Allrights,includingrightscreatedbypatentgrantorregistrationofautilitymodelordesign,arereserved.
Delivery subject to availability. Right of teachnical modification reserved.
DECLARATION OF CONFORMITY
according to FCC Part 15 Class B
This device complies with Part 15 Class B of the FCC Rules. Operations are subject to the following
two conditions:
(1) This device may not be allowed to cause harmful interference, (2) This device must accept any
interference received, including interference that may cause undesired operation.
i
13. Unplug this product from the wall outlet and refer servicing to qualified service personnel under
the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are followed. Adjust
only those controls that are covered by the operating instructions since improper adjustment
of other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to normal condition.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.
14. CAUTION. When replacing the battery, be sure to install it with the polarities in the correct
position. There is a danger of explosion if the battery is replaced with an incorrect type or
is mistreated. Do not recharge, disassemble or dispose of in fire. Replace only with the
same or equivalent type recommeded by the manufacturer. Dispose of the used battery
according to the manufacturer’s instructions.
15. Use only the proper type of power supply cord set (provided in your accessories box) for this unit.
Itshouldbeadetachabletype:ULlisted/CSAcertified,BS1363,ASTA,SS145certified,rated10A
250V minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters).
16. NOTE:
PleasetakeextraprecautionwhenconnectingtheLANcable;donotconnecttheLANcable
to the peripheral device’s connector, that might have excessive voltage.
iii
Before reading this manual
This section describes safety precautions and convention used in this manual. Be sure to read this.
For Safe Operation
This manual contains important information for using the DESKPOWER personal computer.
ReadthismanualthoroughlybeforeusingyourPC.Inparticular,“SafetyPrecautions”inthismanual
must be read and understood.
This manual including “Safety Precautions” must be readily available at all times.
ThisequipmentiscompliantwiththePCindustrystandard(PC-11-1988)oftheJapanElectronics
and Information Technology Industries Association.
Note
This product is a Class B Information Technology Equipment and conforms to the standard set by
the Voluntary Control Council for Interference by Technology Equipment (VCCI).This product is
designed to be used in a domestic environment, however, it may cause radio interference when
used in the vicinity of a radio or television receiver.
Make sure that you read the manual when using this product.
Fujitsu, as a member of the International Energy Star Program, recognizes that
this equipment is compliant with the standard of the International Energy Star
Program.
The International Energy Star Program is a worldwide program for promoting
energy saving for computers and other office equipment. The program aims at
promoting the development and use of products equipped with the functions that can effectively
reduce energy consumption and uses a voluntary system that allows enterprises to join at their
own discretion. The target products are office equipment including computers, displays, printers,
facsimiles, and copying machines. The standards for individual types of equipment and the mark
(
) prepared by the Program are used commonly among member countries.
Caution
ThisequipmentisclassBinformationtechnologyequipmentbasedonthestandardoftheVoluntary
Control Council for Interference by Information Technology Equipment (VCCI). Although the
equipmentisintendedforuseinresidentialenvironments, itmaycreateinterferenceifplacednear
radio or television.
Handle the equipment in accordance with the manual.
iv
Using this Product for High-Safety Applications
Thisproductisforoffice,personal,home,ordinaryindustryandothergeneraluse.Itisnotdesigned
and manufactured for use in high-safety applications.
Do not use this product for such applications without taking measures to satisfy the high-safety
requirements.
High-safety applications require extremely high level of safety, and involve serious hazards to life
and health if the required safety is not assured. High-safety applications include the following.
● Nuclearreactioncontrolinnuclearfacilities, automaticaviationcontrol, airtrafficcontrol, mass-
transportation control, life-supporting medical equipment, and missile launch control.
Someparts(includingtheCRTdisplay,LCD,orharddiskdrive)usedonthisproducthavealimited
life. When used continuously for a prolonged period, these parts will need earlier replacement.
Backing Up the Data
Thecustomerisresponsibleformaintainingtheintegrityofdata(includingthebasicandapplication
software)storedorinstalledontheproduct.Wedonotwarranttheintegrityofdatastoredorinstalled
onthepersonalcomputerthecustomersentforrepair.Takeappropriatemeasuressuchasmaking
a backup.
Weassumenoresponsibilityforlossofdataandanydirectorincidentaldamageduetoanycause
other than those specified in the warranty.
This computer is designed for use within the country. If you are using it abroad, please do so on
your own responsibility.
This equipment may be adversely affected by the momentary drop of the supplied voltage due to
lightning. Use of an AC uninterruptible power supply is recommended for measures against the
momentary drop of the supplied voltage.
(This message is based on the Japan Electronics and Information Technology Industries
Association’s guidelines for measures against momentary voltage drop in PCs.)
Since this equipment contains special materials controlled by the Foreign Exchange and Foreign
Trade Control Law. Authorization under the law may be required to export this equipment.
v
Microsoft Service Pack
MicrosoftCorp. offersServicePacktoprovidetheusersofMicrosoft® Windows® withmorestable
system operation (http://www.microsoft.com/).
ThelatestversionoftheServicePackhelpsyouconfigurethemoststablesystemusingMicrosoft®
Windows® provided at that time by Microsoft Corp.
We recommend you to use the latest version.
In some environments, however, the Service Pack may cause unexpected failure. Read
Readme.txt for the Service Pack before use.
Again, we recommend you to make a system backup in case of failed installation.
Components of this product (motherboard, CD-ROM, hard disk, and floppy disk drive) contain
traces of heavy metals (lead and chrome) and chemical (antimony).
vi
Conventions Used in This Manual
Introduction
This manual tells you how to put your PC into operation and how to operate it in daily use.
Depending on the configuration level chosen some of the hardware components described may not
be available on your PC. Please observe the notes on your operating system.
You can incorporate operable drives (for example DAT drive) as well as other boards.
Depending on the configuration selected, the operating system is preinstalled on your hard disk (e.g.
Windows XP).
Your PC has a number of security features to ensure that no unauthorised persons can access your
data, for example, you can activate a screen saver with password protection. For example, you can
activateascreensaverwithpasswordprotection. ThesecurityfunctionsintheBIOSSetupalsoallow
you to protect your data by means of passwords.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
Indicates information which is important for your health or for preventing
CAUTION
physical damage.
Indicatesimportantinformationwhichisrequiredtousethesystemproperly.
ꢀ Text which follows this symbol describes activities that must be performed in the order shown.
Text in this typefaceindicates screen outputs.
"Quotation marks" indicate names of chapters or terms.
vii
Important Notes
Inthischapteryouwillfindinformationregardingsafetywhichisessentialtotakenoteofwhenworking
with your PC. The manufacturer's notes contain helpful information on your PC.
ꢁ Safety
CAUTION
During installation and before operating the device, please observe the instructions on
environmentalconditionsinthechapterentitled"Technicaldata"aswellastheinstructionsinthe
chapter "Preparing for Use".
Please check whether the device is correctly set for the local power supply (see "Preparing for
Use" chapter).
ThemainswitchandtheON/OFFswitchdonotdisconnectthesystemunitfromthemainsvoltage.
To completely disconnect the mains voltage, remove the power plug from the grounded mains
outlet.
Replacethelithiumbatteryonthesystemboardinaccordancewiththeinstructionsinthe"System
expansions - Replacing lithium battery" chapter.
Caution: components in the system can get very hot.
ꢁ Manufacturer’s notes
Keep this operating manual together with your device. If you pass on the device to third parties,
you should include this manual.
ꢁ Energy saving
When the PC is delivered, some energy-saving functions are already set
ꢀ
ꢀ
ꢀ
If you are not using your PC, switch it off.
In the BIOS Setup you may set further energy-saving functions for the PC.
Depending on the operating system, you can set additional power-management features.
Energy saving under Windows 2000/XP
The Screen Saver tab allows you to set energy-saving functions for your screen. Select the
following item in the menu: Start → Settings → Control Panel → Display → Display Properties →
Screen Saver → Energy saving features of monitor.
With the default setting Control Panel → Power Options → Advanced additional power
management features of Windows 2000/XP are available.
viii
ꢁ FCC Class B Compliance Statement
Thefollowingstatementappliestotheproductscoveredinthismanual,unlessotherwisespecified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital device,
pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-
Causing Equipment Regulations. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in strict accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guaranteethatinterferencewillnotoccurinaparticularinstallation. Ifthisequipmentdoescause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
ꢀ Reorient or relocate the receiving antenna.
ꢀ Increase the separation between equipment and the receiver.
ꢀ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
ꢀ Consult the dealer or an experienced radio/TV technician for help.
Fujitsu is not responsible for any radio or television interference caused by unauthorised
modifications of this equipment or the substitution or attachment of connecting cables and
equipment other than those specified by Fujitsu. The correction of interference caused by such
unauthorised modification, substitution or attachment will be the responsibility of the user.
TheuseofshieldedI/Ocablesisrequiredwhenconnectingthisequipmenttoanyandalloptional
peripheral or host devices. Failure to do so may violate FCC rules.
ix
ꢁ Transporting the PC
CAUTION
Transport all parts separately in their original packaging or in a packaging which protects them
from knocks and jolts, to the new site. Do not unpack them until all transportation manoeuvres
are completed.
Never drop the monitor!
ꢁ Cleaning the PC
CAUTION
Turn off all power and equipment switches and remove the power plug from the mains supply.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
Ensure that no liquid enters the system.
Ensure that the ventilation areas of the system unit and the monitor are free.
Cleaning the system unit and the monitor
Wipe the system unit and monitor casing with a dry cloth. If particularly dirty, use a cloth that has
been moistened in mild domestic detergent and then carefully wrung out.
Cleaning the keyboard and the mouse
Use disinfectant wipes to clean the keyboard and the mouse.
The mouse mechanism and the mouse ball can be cleaned by removing the retaining ring on the
underside of the mouse.
Additional information can be found in the documentation for your keyboard and mouse.
x
ꢁ Disposal and recycling
This device has been manufactured to the highest possible degree from materials which can be
recycled or disposed of in a manner that is not environmentally damaging. The device may be taken
back after use to be recycled, provided that it is returned in a condition that is the result of normal use.
Any components not reclaimed will be disposed of in an environmentally acceptable manner.
Do not throw lithium batteries into the household waste. They must be disposed of in accordance
with local regulations concerning special waste.
Reference to products
In this manual, the product names are referred to as follows:
This manual includes information on other operating systems.
Product name
Microsoft® Windows® XP Professional
Description used in the manual
Windows XP
Professional
Windows
Microsoft® Windows® XP Home Edition
Microsoft® Windows® 2000 Professional
Windows XP
Home Edition
Windows*
XP
Windows 2000
xi
Warning and caution labels
Your PC bears the warning and caution labels as shown below.
The warning and caution labels must not be removed or damaged.
Rear of the PC main unit
To prevent electric shock,
switch off the PC and
WARNING
connected peripherals and
unplug power cords from
respective outlets before
disassembling the unit and
installing a built-in option.
Electric shock
Inside the PC main unit
WARNING
To prevent electric
Electric shock
shock and/or fire, do
not remove the cover
of this unit, which
includes a high
voltage section.
ATTENTION
115V of voltage switch in the power supply corresponds to 100-127V
230V of voltage switch in the power supply corresponds to 200-240V
WARNING
• Before mounting or dismounting an optional unit in/from your PC, switch off
the PC and all connected units and unplug all power cords from respective
outlets to prevent electric shock.
xii
Organization of This Manual
Before Reading This Manual
This section contains cautions for safe operation, representations and symbols used in this manual.
Be sure to read this first!
Chapter 1 Preparing for Use
This chapter provides the names and functions of individual parts.
Chapter 2 Operation
Thissectiondescribesthelocationofinstallationandinstallationofthecomputer.
Chapter 3 Troubleshooting and Tips
This chapter provides the basic information on the PC and operation.
Chapter 4 System Expansion
Thischapterprovidesbasicinformationonhowtohandletheperipheralsinstalled
(or can be installed) on the PC.
Chapter 5 Technical Data
This chapter describes the specifications of this PC.
xiii
Contents
CHAPTER 1
Preparing for Use
1
Preparing for Use..............................................................................2
Unpacking and Checking the Delivery ............................................................. 2
Steps for Initial Setup ....................................................................................... 2
Setting Up the PC ............................................................................................ 3
Connect the Monitor, Mouse and Keyboard ..................................................... 3
Connecting the PC to the Mains Voltage.......................................................... 5
Initial Switch-on: Software will be Installed....................................................... 6
Connecting External Devices ........................................................................... 8
CHAPTER 2
Operation
1
Operation .........................................................................................12
Switching On the PC ...................................................................................... 12
Switching Off the PC ...................................................................................... 13
Indicators on the PC....................................................................................... 14
2
3
Keyboard .........................................................................................15
Floppy Disks ...................................................................................17
Working with Floppy Disks ............................................................................. 17
Settings in BIOS Setup .................................................................................. 18
Property and Data Protection......................................................................... 18
Access Protection Under Windows ................................................................ 18
BIOS Setup Security Functions...................................................................... 19
CHAPTER 3
Troubleshooting and Tips
1
Troubleshooting and Tips ..............................................................22
Installing New Software .................................................................................. 22
Power-on Indicator Remains Unlit After You Have Switched on Your Device . 22
No Mouse Pointer Displayed on the Screen................................................... 24
The Floppy Disk Cannot be Read or Written.................................................. 24
Time and/or Date is Not Correct .................................................................... 25
Tips ................................................................................................................ 25
xiv
CHAPTER 4
System Expansion
1
System Expansions ........................................................................28
Information about boards ............................................................................... 28
Opening the casing ........................................................................................ 29
Closing the casing .......................................................................................... 29
Installing and Removing a Board ................................................................... 30
Low-Profiles boards ....................................................................................... 34
Installing an Additional Serial Port ................................................................. 34
Installing and Removing the Hard Disk Drives ............................................... 35
Replacing Lithium Battery .............................................................................. 37
CHAPTER 5
Technical Data
1
Technical Data.................................................................................39
Electrical Data ................................................................................................ 40
xv
xvi
CHAPTER 1
Preparing for Use
1 Preparing for Use
CAUTION
Please take note of the safety information in the "Important notes" chapter.
■ Unpacking and Checking the Delivery
It is recommended not to throw away the original packaging material! It may be required for
reshipment at some later date.
■
■
■
Unpack all the individual parts.
Check the delivery for damage incurred during transportation.
Check whether the delivery agrees with the details in the delivery note.
Should you discover that the delivery does not correspond to the delivery note, notify your local
sales outlet immediately.
■ Steps for Initial Setup
First-time setup includes the connection of the monitor, mouse and keyboard to the system unit
and the setup of the supplied software.
■
■
External devices
If you have received other devices in addition to your PC (e.g. a printer or a modem), do
not connect these until after the initial installation. The following sections contain a
description of how to connect these external devices: "Connecting external devices to
the serial port" and "Connecting external devices to the parallel port".
Drives and boards
If you have received drives or boards with your PC, please do not install them until after
first-time setup. How to install drives and boards is described in the chapter "System
expansions".
Perform the following steps in the prescribed order:
1. Decide where you are going to use the PC, and then set it up.
2. Connect the monitor, mouse and keyboard to the PC.
3. Check the rated voltage of the PC and connect it to the mains voltage.
4. Switch the PC on and follow the instructions on the screen.
2
■ Setting Up the PC
CAUTION
When installing your PC, give consideration to the recommendations and safety notes.
Set up the PC only in its correct orientation. The points to observe are illustrated on the following
pages.
We recommend that you place your equipment on a surface with good anti-slip qualities. In view
of the multitude of different finishes and varnishes used on furniture, it is possible that the rubber
feet of the devices will mark the surface they stand on.
Do not expose the PC to extreme environmental conditions (see chapter "Technical data") and
protect it from dust, humidity and heat.
Provide at least 200 mm of clearance on the left, in front of and behind the ventilator area of the
system unit to ensure adequate ventilation. Do not cover the ventilation areas of the monitor and
the system unit.
Do not place several system units one above the other.
■ Connect the Monitor, Mouse and Keyboard
The ports for monitor, mouse and keyboard are on the rear and on the front of the system unit.
PS/2 keyboard port / purple
Monitor port / blue
PS/2 mouse port / green
USB port / black
ꢀ Connecting the keyboard
Connecting standard keyboard
Use the supplied keyboard cable only.
■
Plug the round keyboard cable connector into the port marked with this symbol on the
system unit.
3
ꢀ Connecting the mouse
Connecting a PS/2 mouse
■
Connect the PS/2 mouse to the PS/2 mouse port on the system unit.
Connecting USB mouse
Connect the USB mouse to the USB port
■
on the system unit.
IfyoudonotattachamouseatthePS/2mouseport , youcandisablethemousecontroller
in the BIOS Setup in order to free the IRQ12 for a different application.
4
■ Connecting the PC to the Mains Voltage
100 V - 127 V
100 V - 127 V
a
a
200 V - 240 V
200 V - 240 V
a = Notch for inserting the screwdriver
3
Check the voltage setting.
1
Notch for inserting the screwdriver
If the power supply of your PC does not have a slide-in or plug-in element for setting the rated
voltage, thenyoursystemautomaticallysetsitselftothelocalratedvoltage. IfyouhaveaPCwith
a slide-in or plug-in element, then you must match the set rated voltage to the local rated voltage.
ꢁ
Check the voltage setting.
CAUTION
ꢁ
Devices with main power switch:
The value indicated with an arrow must be compatible with the local rated voltage:
• 115 = 100 V to 127 V
• 230 = 200 V to 240 V
If the voltage setting is incorrect, then lift out the manual voltage adjuster with a screwdriver (1),
turn it to the required setting and reinsert it.
ꢁ
Devices without main power switch:
The visible value must agree with the local mains voltage:
• 115 = 100 V to 127 V
• 230 = 200 V to 240 V
Ifanincorrectmainsvoltageisset,pushtheslideswitchallthewayintotheotherpossibleposition
with a pointed object.
5
2
1
ꢁ
Plug the system unit's power cable into the system unit (1) and then into the grounded mains
outlet (2).
■ Initial Switch-on: Software will be Installed
If the PC is connected to a network, the network protocol is required as well as the user and server
details. Contact your network administrator if you have any questions about these settings.
When you switch on your PC for the first time, the supplied software is installed and configured. You
should plan some time for this, as this process must not be interrupted.
CAUTION
Once the installation has been started the PC must not be switched off!
During installation the PC may only be rebooted when you are requested to do so!
Otherwisetheinstallationwillbenotbeperformedcorrectly.Ifafaultoccursduringtheinstallation,
the contents of the hard disk must be completely restored.
You may need the licence number for Windows during the installation. This number is located on
a sticker on your PC.
ꢀ Switching on monitor and PC
ꢁ
Switch the monitor on (see the operating manual for the monitor).
Switch the PC on. To do this, follow the instructions below.
ꢁ
6
Switching on PC with devices with main power switch
1
1
ON/OFF switch
ꢁ
Press the ON/OFF switch on the front of the PC.
The power-on indicator lights green and the PC is started.
ꢀ Installing the software
ꢁ
During installation, follow the instructions on screen.
Consult the operating system manual if there is anything unclear about the requested input data.
You will find further information about the drivers on the "Composite/Software Drivers" CD.
7
■ Connecting External Devices
CAUTION
Do not connect or disconnect cables during a thunderstorm.
Always take hold of the actual plug. Never unplug a cable by pulling the cable itself.
Connect and disconnect the cables in the order described below.
With the exception of USB devices, always remove all power plugs before connecting external
devices!
Read the documentation on the external device before connecting it.
Connecting cables
ꢁ
ꢁ
ꢁ
Turn off all power and equipment switches.
Pull all power plugs out of grounded mains outlets.
Connect all cables at the system unit and peripherals. You must observe the information
provided in the chapter "Important notes".
ꢁ
ꢁ
Plug all data communication cables into the utility sockets.
Plug all power cables into the grounded mains outlets.
Disconnecting cables
ꢁ
ꢁ
ꢁ
ꢁ
Turn off all power and equipment switches.
Pull all power plugs out of grounded mains outlets.
Unplug all data communication cables from the utility sockets.
Disconnect all cables from the system unit and peripherals.
USB devices are hot-pluggable. This allows cables from USB devices to be connected and
disconnected with the system switched on.
Additional information can be found in the documentation for the USB devices.
8
ꢀ Connections on the system unit
The ports for external devices are on the rear and on the front of the system unit. The ports available
on your PC depend on the configuration level you have selected. The standard ports are marked with
the symbols shown below (or similar).
Keyboard port / purple
PS/2 mouse port / green
1
Serial interface 1 / turquoise
Monitor port / blue
Parallel interface / Printer / burgundy
Microphone jack (mono) / pink
Audio output (Line out) / lime green
Audio input (Line in) / light blue
USB - Universal Serial Bus / black
LAN
LAN connector
Some of the devices that you connect require special drivers (see the operating system and
device documentation).
9
ꢀ Connecting external devices to the serial port
External devices can be connected to the serial port (e.g. a modem).
ꢁ
ꢁ
Connect the data cable to the external device.
Connect the data cable to the serial port
.
For an exact description of how to connect external devices to the serial port , please refer to the
device documentation.
ꢁ Settings of the serial port
If you need to change the settings of the serial port (e.g. address, interrupt), you can do so
in the BIOS Setup.
ꢁ Device drivers
The devices connected to the serial port require drivers. Your operating system already
includes many drivers. Nevertheless, if the driver you need is not on the hard disk, please
install it from the data carrier supplied with the device or with the application programme.
ꢀ Connecting external devices to the parallel port
External devices can be connected to the parallel port (e.g. a printer).
ꢁ
ꢁ
Connect the data cable to the external device.
Connect the data cable to the parallel port
.
Foranexactdescriptionofhowtoconnectexternaldevicestotheparallelport, pleaseseethedevice
documentation.
ꢁ
ꢁ
Settings of the parallel port
If you need to change the settings of the parallel port (e.g. address, interrupt), you can do
so in the BIOS Setup.
Device drivers
Thedevicesconnectedtotheparallelportrequiredrivers.Youroperatingsystemalready
includesmanydrivers. Nevertheless, ifthedriveryouneedisnotontheharddisk, please
install it from the data carrier supplied with the device or with the application programme.
10
CHAPTER 2
Operation
1 Operation
ꢀ Switching On the PC
ꢁ
Switch the monitor on (see the operating manual for the monitor).
On devices with main power switch
ꢁ
ꢁ
Switch the PC on with the main power switch on the back panel.
If the power-on indicator lights orange or flashes green/orange, press the power button on the
front of the casing.
The power-on indicator lights green and the PC is started.
If you have assigned the system password, you must enter this when requested to do so in
order to start the operating system.
On devices without main power switch
ꢁ
If the power-on indicator lights orange or flashes green/orange, press the power button on the
front of the casing.
The power-on indicator lights green and the PC is started.
If you have assigned the system password, you must enter this when requested to do so in
order to start the operating system.
12
ꢀ Switching Off the PC
On devices with main power switch
ꢁ
ꢁ
Shut down the operating system properly. For Windows: select Shut Down from the Start menu.
IftheoperatingsystemdoesnotautomaticallyswitchoffthePC,switchthePCtoready tooperate
by pressing the power button or turn it off by pressing the main power switch when requested to
do so.
If the PC is ready-to-operate, the power-on indicator is illuminated orange. The PC uses minimal
energy.
WhenthePCisswitchedoffwiththemainpowerswitch, thepower-onindicatorgoesoffafterapprox.
15 seconds. The PC no longer uses any power.
CAUTION
The main power switch and the power button do not disconnect the PC from the mains voltage.
To completely disconnect the mains voltage, remove the power plug from the socket.
ꢁ
Switch the monitor off.
On devices without main power switch
ꢁ
ꢁ
Shut down the operating system properly. For Windows: select Shut Down from the Start menu.
If the operating system does not automatically switch the PC off, turn the PC to ready-to-operate
when requested to do so by pressing the power button.
If the PC is ready-to-operate, the power-on indicator is illuminated orange. The PC uses minimal
energy.
CAUTION
The power button does not disconnect the PC from the mains voltage. To completely disconnect
the mains voltage, remove the power plug from the socket.
ꢁ
Switch the monitor off.
13
■ Indicators on the PC
The indicators are on the front of the casing.
1 2
4
3
1
2
Hard disk indicator
The indicator lights up when the hard disk drive of the PC is accessed.
Power-on indicator
–
The indicator lights green:
The PC is on.
–
The indicator lights orange:
The PC is in energy-saving mode. After being switched on with the power button, the PC
switches on or returns to the state it was in before the energy-saving mode.
CAUTION
Inanenergy-savingmodethePCmustnotbeswitchedoffwiththemainpowerswitch(ifpresent)
or disconnected from the mains, as this may result in data loss.
–
The indicator does not light up:
The PC is switched off (power switch at 0 or disconnected from the power supply) or ready-
to-operate. If the PC is ready-to-operate, the PC can be enabled with the ON/OFF switch.
3
4
Floppy disk indicator
The indicator lights up when the floppy disk drive of the PC is accessed. You may only remove
the floppy disk when the indicator is unlit.
CD-ROM indicator
The indicator lights up when the CD-ROM drive is accessed. You may only remove the CD when
the indicator is dark.
14
2 Keyboard
1
2
3 4
5
6
7
20
8
9
10 11
12 13 14 15 16 17 18
19
1
2
3
4
5
6
7
Esc key
Pressing this key cancels the operation the application program is executing.
F keys
These F keys are assigned specific functions for each application.
Back space key
Press the Back Space key to move the cursor to the left while deleting characters.
Insert key
Press the Insert key to switch between character insert mode and overwrite mode.
Print Screen key
Pressing this button copies the screenshot to the clipboard.
Home key
Press the Home key to move the cursor all at once to the beginning of the current line or text.
Indicators
The indictor lights when you press [Num Lock], [Shift] + [Caps Lock], or [Scroll Lock], indicating
that it is enabled. When the key is pressed again, the indicator turns off and the key function is
disabled.
8
Caps Lock key
Use the Caps Lock key to type alphabetical characters.
Press [Shift] + [Caps Lock] to switch between uppercase and lowercase.
15
9
Ctrl key
Use the Ctrl key in combination with another key. Its function varies with each application.
10 Windows key
Press the Windows key to display the Start menu.
11 Alt key
Use the Ctrl key in combination with another key. Its function varies with each application.
12 Application key
This key has the same function as clicking the right mouse button.
Press this key to display the shortcut menu of the selected item.
13 Enter key
The Enter key is also referred to as the Return key.
Press this key to perform line feed or execute a command.
14 Delete key
Press the Delete key to delete a character. Press this key together with [Ctrl] and [Alt] to reset the
computer.
15 End key
Press the End key to move the cursor all at once to the end of the current line or text.
16 Cursor keys
Press each of these keys to move the cursor in the desired direction.
17 Page Down key
Scrolls down the on-screen page when pressed.
18 Page Up key
Scrolls up the on-screen page when pressed.
19 Numeric keypad
Enables you to enter numerals when the [Num Lock] indicator is on.
Thefunctiondescribedinthelowerpartofthenumerickeyisenabledwhenthe[NumLock]indicator
is off.
20 Num Lock key
Press the Num Lock key to change the Ten-key pad functions.
ꢀ Point
To tilt the keyboard, pull up the tilt foot on the both sides of the underside of the keyboard.
Tilt foot
16
3 Floppy Disks
I Working with Floppy Disks
Follow the instructions supplied by the vendor of the floppy disks.
Never clean the floppy disk drives with cleaning disks. Any attempt would destroy the read/
write head in the disk drive within 20 seconds.
5
7
6
4
1
2
3
1
Insertion direction
Label area
2
3
Write protection switch for a 720 KB or a 1.44 MB floppy disk
4
5
6
7
Identification of a 1.44 MB floppy disk or write protect switch on a 120 MB floppy disk
Eject button for inserted floppy disks
Disk is write-protected
Disk is not write-protected
ꢁ
To insert a floppy disk, push it into the drive in the insertion direction until it engages. The
label should be facing upward.
ꢁ
To remove the floppy disk, press the eject button (5).
The write-protect switch enables you to protect the data on the floppy disk from inadvertent
overwriting or deletion.
ꢁ
To protect the data on the floppy disk from being overwritten, push the write-protect switch to
position (6). The hole is now visible.
ꢁ
To remove write protection, push the switch to position (7). The hole is now covered.
17
IISettings in BIOS Setup
TheBIOSSetupmenuallowsyoutosetyourhardwareconfigurationandsystemfunctions.When
the PC is delivered, the default entries are valid. You may customise these settings to your
requirements in the BIOS Setup.
I Property and Data Protection
Software functions and mechanical locking offer a broad range of functions for protecting your
PC and your personal data from unauthorised access. You can also combine these functions.
ꢂ Anti-theft protection
There are two ways to protect your PC from theft:
ꢁ
with a chain and the eyelet (1)
ꢁ
with the Kensington Lock device (2) and with a Kensington MicroSaver
To prevent unauthorised persons from opening the casing, the casing can be sealed. To do this,
use the eye on the top cover (1) and the eye on the back of the casing (2).
You can also attach a padlock to the eye (1) to prevent unauthorised opening of the casing.
2
1
Kensington Lock
I Access Protection Under Windows
Under MS-Windows you can activate a screen saver and protect it with a password. Only those
userswhoknowthepasswordcandeactivatethescreensaverandaccessanyopenfiles.Detailed
information on screen savers is provided by the associated help function.
18
I BIOS Setup Security Functions
The Security menu in BIOS Setup offers you various options for protecting your personal data
against unauthorised access, e.g.:
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
Preventing unauthorised BIOS Setup entry
Preventing unauthorised system access
Preventing unauthorised access to the settings of boards with their own BIOS
Preventing system booting from the diskette drive
Preventing unauthorised writing of diskettes
Protecting BIOS from being overwritten
You can also combine these functions.
19
20
CHAPTER 3
Troubleshooting
and Tips
1 Troubleshooting and Tips
CAUTION
Takecarefulnoteofthesafetywarningsandinthe“PreparingforUse”chapter,whenyouconnect
or disconnect cables.
If a fault occurs, try to correct it as described:
ꢀ
ꢀ
ꢀ
in this chapter
in the documentation of the connected devices
in the help systems of the software used.
If you fail to correct the problem, proceed as follows:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Switch the PC off.
Make a note of the steps and the circumstances that led to the fault.
Make a note of any error messages displayed.
Note the ID number of your device.
Contact your sales outlet or our customer service centre.
■ Installing New Software
When installing programmes or drivers, important files may be overwritten and modified. To be able
toaccesstheoriginaldataintheeventofanyproblemsfollowinginstallation, youshouldbackupyour
hard disk prior to installation.
■ Power-on Indicator Remains Unlit After You Have
Switched on Your Device
This may be due to the following:
The mains voltage supply is faulty
ꢀ
ꢀ
Check that the power cable is plugged properly into the system unit and grounded mains outlet.
Switch the PC on at the power switch.
Internal power supply overloaded
ꢀ
ꢀ
ꢀ
ꢀ
Disconnect the power cable of the system unit from the grounded mains outlet.
Wait for a moment.
Plug the power cable into the grounded mains outlet again.
Switch the PC on at the power switch.
22
ꢁ The screen stays blank
If your screen remains blank this may be due to the following:
Monitor is switched off
ꢀ
Switch your monitor on.
Power saving has been activated (screen is blank)
ꢀ
or
ꢀ
Press any key on the keyboard.
Deactivate the screen saver. Enter the appropriate password.
Brightness control is set too dark
ꢀ
Adjust the brightness control. For detailed information, please refer to the operating manual
supplied with your monitor.
Power cable not connected
ꢀ
Switch off the monitor and the PC.
ꢀ
Check that the power cable of the monitor is properly connected to the monitor and, depending
on the connector, to the system unit or to the grounded mains outlet.
ꢀ
ꢀ
CheckthatthepowercableofthePCispluggedproperlyintothesystemunitandgroundedmains
outlet.
Switch on the monitor and the system unit.
Monitor cable not connected
ꢀ
ꢀ
ꢀ
Switch off the monitor and the system unit.
Check that the monitor cable is properly connected to the system unit and monitor.
Switch on the monitor and the system unit.
23
Wrong monitor has been set under Windows 2000/XP
ꢀ
ꢀ
Restart the PC.
If the message Starting Windows appears, press function key [F8].
The Windows 2000/XP Advanced Options Menu appears.
ꢀ
ꢀ
Select Safe Mode or Safe Mode with Network.
Setthecorrectvaluesfortheattachedmonitorasdescribedintheoperatingmanualofthemonitor
by selecting Start → Settings → Control Panel → Display → Settings.
The wrong RAM modules have been inserted
See the technical manual for the system board for information on which memory modules can be
used.
■ No Mouse Pointer Displayed on the Screen
ꢀ
ꢀ
ꢀ
Shut down the operating system properly.
Switch the PC off.
Check that the mouse cable is properly connected to the system unit.
If you use an adapter or extension lead with the mouse cable, check the connections.
Make sure that only one mouse is connected.
Switch the PC on.
ꢀ
ꢀ
The mouse controller must be enabled if you use a PS/2 mouse on the PS/2 mouse port
.
ꢀ
ꢀ
Check in the BIOS Setup that the mouse controller is Enabled.
Checkthatthemousedriverisproperlyinstalledandispresentwhentheapplicationprogramme
is started. Detailed information can be found in the user guide for the mouse and application
programme.
■ The Floppy Disk Cannot be Read or Written
ꢀ
ꢀ
ꢀ
ꢀ
Check that the floppy disk is not write protected.
Check the relevant entries for Diskette A: or B: in the Main menu of the BIOS Setup.
Check that the floppy disk drive controller is enabled.
Checkthatthecablesofthefloppydiskdriveareproperlyconnected(referto“Changingthefloppy
disk drive” chapter).
24
■ Time and/or Date is Not Correct
You can set the time and date in the BIOS Setup or in the operating system.
ꢀ
Set the time and date.
If the time and date are repeatedly wrong when you switch on your PC, the on-board battery
is flat. Change the lithium battery as described in the "Replacing lithium battery" chapter.
■ Tips
The PC cannot be switched off with the power button
Cause: The PC was not switched on with the power button.
ꢀ
Press the power button again.
Cause: System crash
Press and hold the power button for at least four seconds until the device switches off.
ꢀ
Out of system resources
If you have too many applications running at once, you may experience problems due to a lack of
system resources. In this case you should:
ꢀ
close unnecessary applications
or
ꢀ
run the applications in a different order.
25
26
CHAPTER 4
System Expansion
1 System Expansions
It may be necessary to update the BIOS when carrying out a system expansion or hardware
upgrade. In this case, please contact our customer service centre.
Wheninstallingcomponentswithahighpowerloss,makesurethatthemaximumpermissible
temperatures of the individual components are not exceeded.
The device must be switched off when installing/removing the system expansions and may
not be in the Suspend mode.
This chapter describes all the activities required to modify your PC hardware (e.g. installing boards
or drives).
Read the supplied documentation before installing new drives and/or boards.
ꢀ Information about boards
Takecarewiththelockingmechanisms(catchesandcentringpins)whenyouarereplacingthesystem
board or components on the system board.
To prevent damage to the system board or the components and conductors on it, please take care
when you insert or remove boards. Make sure expansion boards are inserted straightly.
Never use sharp objects (screwdrivers) for leverage.
Boardswithelectrostaticsensitivedevices(ESD)areidentifiablebythelabel
shown.
WhenyouhandleboardsfittedwithESDs,youmust,underallcircumstances,
observe the following points:
ꢁ
Some peripheral devices may not be used on your PC.
ꢁ
You must always discharge static build up (e.g. by touching a grounded
object) before working.
ꢁ
ꢁ
The equipment and tools you use must be free of static charges.
Remove the power plug from the mains supply before inserting or
removing boards containing ESDs.
ꢁ
ꢁ
Always hold boards with ESDs by their edges.
Never touch pins or conductors on boards fitted with ESDs.
28
■ Opening the casing
ꢁ
Switch the PC off. The PC must not be in the energy-saving mode!
CAUTION
Please take note of the safety information in the "Important notes" chapter.
Pull the power plug out of the mains outlet!
ꢁ
ꢁ
ꢁ
ꢁ
If any cables connected to the PC are in the way, disconnect them from the PC
Place the system unit in a convenient working position.
Press on the clip (1).
Push the top cover in the direction of the arrow (2).
2
■ Closing the casing
ꢁ
ꢁ
ꢁ
Push the top cover down in the direction of the arrow (1) until it engages.
Return the PC to its original position.
If you have disconnected cables, reconnect them to the connectors on the rear panel.
29
■ Installing and removing a board
CAUTION
Please take note of the “Information about boards” chapter.
In the upper three slots you can install boards with a length of up to 230 mm, and in the lower slot
boards with a length of up to 315 mm.
The number, position and arrangement of the board slots on the mainboard can be found in the
technical manual for the mainboard. Boards may already be installed when the device is shipped.
ꢂ Installing a board
1
Open the casing (see "Opening the casing").
1
2
3
Remove the screw (1).
Remove the rear slot cover plate from the slot (2).
Do not dispose of the cover plate. For cooling, protection against fire and in order to
comply with EMC regulations, you must refit the cover plate if you remove the board.
The top and the lowest slot are suitable for low-profile cards with an adapter.
4
Take the new board out of its packaging.
30
5
Make the required settings for the board.
2
6
Push the board up to its slot (1).
Ensure that the end of a long board without angle bracket fits into the corresponding guide of the
casing.
7
8
9
Press the board into the slot so that it engages.
Fasten the board into place with the screw (2).
If necessary, connect the cables.
10 Close the casing (see "Closing the casing").
If you have installed or removed a PCI board, please check the relevant PCI slot settings
in the BIOS Setup. If necessary, change the settings. Further information is provided in the
PCI board documentation.
31
ꢂ Removing a board
1
Open the system unit (see "Opening the system unit").
2
Disconnect the cables connected to the board.
1
3
4
5
Remove the screw (1).
Remove the board from the system unit (2).
Place the board into appropriate packaging.
CAUTION
To ensure proper cooling, fire protection and observation of the relevant EMC
(electromagnetic compatibility) regulations, you must mount a rear slot cover plate.
32
2
6
7
8
Push the rear slot cover plate into the slot (1).
Fasten the rear slot cover plate with the screw (2).
Close the casing (see "Closing the casing").
CAUTION
If you have installed or removed a PCI board, please check the relevant PCI slot settings
in the BIOS Setup. If necessary, change the settings. Further information is provided in the
PCI board documentation.
33
■ Low-Profile boards
For units with a particularly low overall height, there are so-called low-profile boards with a slot cover
with a lower overall height to match the low-profile units. To also install these low-profile boards in
normal board slots, you must mount a corresponding slot adapter beforehand.
2
ꢂ Mounting slot adapter
ꢁ
Fit the slot adapter on the slot cover of the low-profile board (1) and screw it on (2).
Now you can install the low-profile board in a suitable slot like a normal board (see the chapter
"Installing board").
1
ꢂ Removing slot adapter
ꢁ
Unscrew the screw (1) and remove the slot adapter (2).
■ Installing an Additional Serial Port
An additional serial interface can be installed in a rear slot cover plate like a board. The condition is
that the system board has a free internal serial port.
ꢁ
Connect the cable of the additional serial port to the connector on the system board.
34
■ Installing and Removing the Hard Disk Drives
ꢁ
Open the casing (see "Opening the casing").
ꢂ Removing a hard disk drive
2
1
1
1
2
PresstheEasyChangerailsmountedontheharddiskdrivetogethersomewhat(1)and
pull the hard disk drive out of the case in the direction of the arrow (2).
Disconnect all cables connected to the drive (data cable, power supply cable).
It may be necessary to modify the entry for the drive in the BIOS Setup.
Connect the cables to the hard disk drive.
3
4
Close the casing (see "Closing the casing").
35
ꢂ Installing a hard disk drive
1
Take the new hard disk drive out of its packaging.
2
3
Make the required settings (e.g. master/slave, cable select) on the drives.
SecuretheEasyChangerailsonthesideoftheharddiskbyinsertingtheupperpinsof
the EasyChange rail in the corresponding holes of the hard disk.
4
Connect the cables to the hard disk drive.
1
2
1
5
6
PresstheEasyChangerailsmountedontheharddiskdrivetogethersomewhat(1)and
slide the hard disk drive into the case in the direction of the arrow (2).
Close the casing (see "Closing the casing").
It may be necessary to modify the entry for the drive in the BIOS Setup.
EasyChange rails for a second hard disk drive are mounted on the drive cage.
36
■ Replacing Lithium Battery
Inordertopermanentlysavethesysteminformation,alithiumbatteryisinstalledtoprovidetheCMOS-
memory with a current. A corresponding error message notifies the user when the charge is too low
or the battery is empty. The lithium battery must then be replaced.
CAUTION
Incorrect replacement of the lithium battery may lead to a risk of explosion!
The lithium battery may be replaced only with an identical battery or with a type
recommended by the manufacturer.
Do not throw lithium batteries into the household waste. They must be disposed of in
accordance with local regulations concerning special waste.
Make sure that you insert the battery the right way round. The plus pole must be on the top!
The lithium battery holder exists in different designs that function in the same way.
1
2
3
Disconnect the USB cable and, if necessary, the audio cable from the mainboard.
Remove the port cover.
Remove the screw (1) and pull the USB interface or the USB audio interface upwards
out of the location (2).
4
5
Remount the blind cover of the bay (3) from the front.
Re-attach the cover (4).
37
38
CHAPTER 5
Technical Data
■ Electrical Data
DESKPOWER P300
Rated voltage range: (selectable)
Frequency:
100 V -127 V / 200 V - 240 V
50 Hz -60 Hz
Max. rated current
• Casing with monitor socket
100 V -127 V / 6,0 A
200 V -240 V / 3.0 A
100 V -127 V / 3.0 A
200 V -240 V / 1,5 A
• Monitor socket (output)
Dimensions
Width/depth/height:
202 mm/376 mm/372 mm
11 kg in basic configuration
Weight
with the basic configuration
Environmental conditions
Environment class 3K2
Environment class 2K2
DIN IEC 721 part 3-3
DIN IEC 721 part 3-2
Temperature:
• Operating (3K2)
• Transport (2K2)
15 °C .... 35 °C
-25 °C .... 60 °C
Condensation in operating must be
avoided.
Clearance required to ensure adequate
ventilation:
• left
• front
min. 200 mm
min. 200 mm
min. 200 mm
• rear
40
|